Dobinsons' 2" MRA Adjustable Lift Kit suits the Toyota Landcruiser 200 Series (2007-2021) and pairs 3-way externally adjustable monotube remote-reservoir shocks with load-specific coil springs front and rear. The remote reservoir adds oil volume for better heat control on long touring runs and corrugated tracks, while the adjustable damping lets you dial in comfort or firmness for towing. Check exact compatibility for your build using our 200 Series parts finder. In stock in Australia, backed by a Dobinsons manufacturer warranty and fitment support from our team.
Browse all compatible suspension parts for your 2" Mra Lift Kit Toyota Landcruiser 200 using our parts finder.
| Make | Model | Series | Years | Engine |
|---|---|---|---|---|
| Toyota | Landcruiser | 200 Series | 2007-2015 | 4.7L V8 Petrol (2UZ-FE) |
| Toyota | Landcruiser | 200 Series | 2015-2021 | 4.6L V8 Petrol (1UR-FE) |
| Toyota | Landcruiser | 200 Series | 2007-2021 | 4.5L V8 Twin Turbo Diesel (1VD-FTV) |
Not sure if this fits your vehicle? Contact our suspension experts or check our FAQ page.
Choosing the right coil spring rate comes down to what you're carrying day-to-day, not just occasional loads. This MRA kit is available with load-specific front and rear coil options so the springs sit at the correct 2" ride height under your actual accessory weight, rather than sagging under a bull bar and winch or sitting too high with nothing fitted. Tell us about your front bar, winch, long-range fuel tank, drawers, canopy or fridge slide so we can match the spring rate to your setup before you order — common front accessories are a steel bull bar, winch and long-range tank, and common rear accessories are a drawer system, canopy, dual battery tray and water tank.
This kit is best fitted by an experienced 4WD suspension installer or a qualified workshop, since the remote reservoir shocks need bracket mounting and the coil springs need correct seating in the towers. Wheel alignment is mandatory after fitting to bring camber, caster and toe back within factory tolerance at the new 2" ride height. Allow a 500km settling-in period for the springs and shock bushes before fine-tuning the adjustable damping to your typical load. If you're running accessories that shift front weight, pairing this kit with upgraded control arms helps correct geometry and CV angles at the new height.
Dobinsons is an Australian-owned suspension manufacturer that has built 4WD lift kits for local conditions for decades, from coastal sand tracks to remote outback corrugations. This MRA kit is backed by a Dobinsons manufacturer warranty and is fitted by workshops around the country on touring and towing builds. You can view the full Dobinsons range to see matching shocks, springs and accessories for other vehicles in your fleet.
This kit suits 200 Series owners who tow a caravan or trailer, run a loaded canopy or drawer system, or spend real time on corrugated outback roads where a fixed-rate shock starts to fade. Tradespeople carrying tools daily and tourers running a rooftop tent, fridge and long-range tank both benefit from the adjustable damping and load-specific springs. If your rear load varies a lot from trip to trip, it's also worth comparing this against airbag suspension as a load-levelling option.
This Dobinsons 2" MRA kit for the Landcruiser 200 Series is in stock in Australia for fast dispatch, with fitment guidance from our in-house team on spring rate and control arm pairing. Browse our full lift kit range or contact us to confirm fitment before you order.
This kit is designed for the Toyota Landcruiser 200 Series across the 2007-2021 model run, covering the 4.7L V8 petrol, 4.6L V8 petrol and 4.5L V8 twin turbo diesel variants. Because coil spring rates can be matched to accessories you already run, it's worth confirming your exact build with our team before ordering. Fitment covers standard wheelbase 200 Series wagons. Use our parts finder or contact us if you're unsure of your exact variant.
This MRA kit provides a 2" lift at both the front and rear of the Landcruiser 200 Series, achieved through the combination of the monotube remote-reservoir shocks and load-specific coil springs. Actual ride height can vary slightly depending on which spring rate is selected for your accessory load. A 2" lift is a common, alignment-friendly height that keeps handling close to factory feel while adding clearance.
The kit includes 2 x front and 2 x rear Dobinsons MRA adjustable monotube remote-reservoir shock absorbers, along with 2 x front and 2 x rear load-specific coil springs. Mounting brackets, bushes, sleeves and fitting hardware are included, plus a technical data sheet. Upper and lower control arms are not included and are sold separately if your build needs them.
Yes. The remote reservoir design gives the shocks more oil volume than a standard twin-tube shock, which helps control heat build-up when towing a caravan or trailer on longer runs. The load-specific rear coil springs can also be matched to your typical towball or accessory load so the rear doesn't sag under a loaded setup. Adjustable damping lets you firm up the rear specifically for towing trips.
Not always, but it's worth considering if you're running a bull bar, winch or other front-end accessories alongside the lift. Upgraded control arms help correct front suspension geometry and CV joint angles at the new 2" ride height. Our team can advise whether your specific accessory combination needs a control arm upgrade or whether the standard arms will do the job.
Yes, wheel alignment is mandatory after installing this kit. Camber, caster and toe all change once the vehicle sits at the new 2" ride height, and correct alignment protects tyre wear and keeps steering feel consistent. We recommend booking an alignment straight after fitment, and again after the 500km settling-in period.
Yes. This MRA kit is available with load-specific front and rear coil spring options so you can match the rate to your actual accessory weight, such as a bull bar, winch, drawers or canopy. Selecting the correct rate keeps the vehicle sitting level at the intended 2" height rather than sagging or riding too high. Speak with our team about your accessory list before ordering so we can recommend the right combination.
A 2" lift typically creates useful extra clearance for a moderately larger tyre, though the exact size that will fit depends on your wheel width, offset and guard trimming. We recommend checking tyre and guard clearance for your specific wheel setup before buying tyres. Our team can talk through common tyre sizes that owners run on a 200 Series at this lift height.
This kit is covered by a Dobinsons manufacturer warranty against manufacturing defects in the shocks and springs. Warranty terms and the claims process are handled through our team, so contact us with your order details if you ever need to make a claim. We can confirm the current warranty period for this specific kit at the time of purchase.
Yes. The 3-way externally adjustable damping lets you soften the shocks for everyday driving and firm them up when towing or loaded for a trip, so you're not locked into one setting. Combined with load-specific coil springs, the ride stays composed on-road at the 2" height rather than feeling bouncy or overly stiff. Many 200 Series owners run this kit as their daily driver as well as their touring setup.
Help other 4WDSuspension users shop smarter by writing reviews for products you have purchased.
Add your favourites to cart
Log into or create your Afterpay account, with instant approval decision
Your purchase will be split into 4 payments, payable every 2 weeks
All you need to apply is to have a debit or credit card, to be over 18 years of age, and to be a resident of country offering Afterpay
Late fees and additional eligibility criteria apply. The first payment may be due at the time of purchase
For complete terms visit afterpay.com/terms
