Reviewed by Andrew, 4WD Suspension fitment team
Airbag Man coil-insert air helper kit for the rear coils of the Toyota LandCruiser Prado 90 & 95 Series. Choose the standard kit (CR5004) for towing and touring loads, or the high pressure kit (CR5004HP) with internal bump stop for heavy constant loads.
Airbag Man helper kits use coil-insert air springs that sit inside the existing coils – add air when the load goes on to bring the vehicle back level, then let it out and the standard springs carry on exactly as before. Because each side inflates independently, you can also correct for an off-centre load like a slide-on or water tank.
They shine when the load keeps changing – a van on the towball some weekends, a loaded tray on others. Worth being clear about what they don't do: helper airbags don't increase your GVM or payload; they manage ride height and stability within the vehicle's existing ratings. If the vehicle is always loaded, upgraded springs (with airbags for the variation on top) is the better setup.
Doing the whole vehicle at once? We also stock the matching front Coil Springs and rear Coil Springs for the Toyota Prado 90 & 95 Series.
| Make | Model | Series | Years |
|---|---|---|---|
| Toyota | LandCruiser Prado | 90 & 95 Series | 07/1996 - 2003 |
Match your vehicle and its current rear ride height to the part number. HP (high pressure) versions carry the same fitment but run up to 60 psi for constant heavy loads or regular towing.
| Part number | Ride height | Pressure range | Suits |
|---|---|---|---|
| CR5004HP | Standard Height | 5 psi - 60 psi | LAND Cruiser Prado 90 & 95 Series KZJ, RZJ &VZJ 96-02; LAND Cruiser Prado 90 & 95 Series NZ Import 96-03 |
| CR5004 | Standard Height | 5 psi - 30 psi | LAND Cruiser Prado 90 & 95 Series KZJ, RZJ &VZJ 96-02; LAND Cruiser Prado 90 & 95 Series NZ Import 96-03 |
The air springs sit inside the existing rear coils, so the factory springs stay in place. Air lines run to two inflation valves, usually mounted at the rear bar, so each side adjusts on its own. Run 5 psi unloaded and add pressure to bring the vehicle back to level when towing or loaded, up to 30 psi on the standard kit or 60 psi on the HP kit. Airbag Man notes that drilling and cutting are required for this fitment, so allow extra workshop time. Typical fitting time is 120 minutes.
Last updated: 9 September 2026
Genuine Airbag Man suspension from an authorised Australian dealer.
New to Prado and FJ Cruiser suspension? Read our Prado and FJ Cruiser suspension problems guide.
| Specification | Detail |
|---|---|
| Kit type | In-coil air helper kit (fits inside the existing rear coil springs) |
| Position | Rear axle |
| Part CR5004HP | 5 psi - 60 psi |
| Part CR5004 | 5 psi - 30 psi |
| Typical fitting time | 120 minutes |
| Fitting notes (Airbag Man) | Drilling & Cutting Required |
| Kit contents | 2 x Airbag Man in-coil air helper springs, mounting hardware, air line tubing, fittings, 2 x inflation valves and step-by-step fitting instructions. HP kits add high-pressure sleeves and end protectors. |
| Warranty | Airbag limited lifetime manufacturer's warranty on the air springs |
Figures from Airbag Man product data. Helper kits assist the springs and do not change the vehicle's GVM or towing capacity.
These suit the following applications: Toyota LandCruiser Prado 90 & 95 Series 07/1996 - 2003. Check your build date and variant against the fitment table on this page – if you're not certain, contact us with your rego or VIN details and we'll confirm fitment before you order.
No – this is the most common misconception about helper kits. Airbags manage ride height and stability within the vehicle’s existing ratings; they don’t change what it’s legally allowed to carry. We’ve written up the details in our guide: do airbags increase GVM or payload?
None at rest. This is a helper kit, not a lift kit. It stops the rear sagging under load: add air to restore factory ride height when towing or loaded, then drop the pressure for unloaded driving.
2 x Airbag Man in-coil air helper springs, mounting hardware, air line tubing, fittings, 2 x inflation valves and step-by-step fitting instructions. HP kits add high-pressure sleeves and end protectors.
The standard kit runs 5 psi - 30 psi. The HP kit adds a high-pressure sleeve over the air spring and runs 5 psi - 60 psi, for constant heavy loads or regular towing near the vehicle's limits. Both carry the same fitment and the same lifetime air spring warranty.
No. The kit includes inflation valves, so you can set pressure at a servo or with a portable 12V compressor. An onboard air control kit only adds in-cab adjustment.
Help other 4WDSuspension users shop smarter by writing reviews for products you have purchased.
Add your favourites to cart
Log into or create your Afterpay account, with instant approval decision
Your purchase will be split into 4 payments, payable every 2 weeks
All you need to apply is to have a debit or credit card, to be over 18 years of age, and to be a resident of country offering Afterpay
Late fees and additional eligibility criteria apply. The first payment may be due at the time of purchase
For complete terms visit afterpay.com/terms
