The Dobinsons 2" MRA Adjustable Strut Kit suits the Toyota Land Cruiser 200 Series (2007-2021) and arrives pre-assembled with 50mm bore monotube remote-reservoir shock absorbers and 3-way external damping adjustment. The kit includes matched Dobinsons coil springs, new top mounts and C-spanners, delivering a 2" front lift without needing spring compression tools. Independent high-speed compression, low-speed compression and rebound adjusters let you tune the ride for towing, touring or unladen daily driving. Backed by manufacturer warranty, held in stock in Australia, with fitment support from our suspension team.
Browse all compatible suspension parts for your 2" Mra Adjustable Strut Kit Land using our parts finder.
| Make | Model | Series | Years | Engine |
|---|---|---|---|---|
| Toyota | Land Cruiser | 200 Series (UZJ200, VDJ200, URJ202) | 2007-2021 | 4.5L V8 Twin Turbo Diesel (1VD-FTV), 4.7L V8 Petrol (2UZ-FE), 4.6L V8 Petrol (1UR-FE) |
Not sure if this fits your vehicle? Contact our suspension experts or check our FAQ page.
Choose your spring rate based on the constant accessory weight sitting on the front of your 200 Series, not occasional gear. Common constant front loads include a bullbar, winch, driving lights, dual battery tray and long-range fuel tank. If you're unsure of your total constant load, our team can help you match the correct spring rate before you order — fitting a spring rated too heavy for your actual load will give a harsh ride.
This kit is pre-assembled, but fitting is still a suspension job best handled by an experienced installer or workshop familiar with the Land Cruiser 200 platform. A wheel alignment is mandatory after installation to reset caster and camber to specification. Allow a 500km bedding-in period for the springs and shock seals to settle before final alignment. If you're running heavier constant loads or want to correct geometry further at ride height, consider pairing this kit with upgraded control arms.
Dobinsons has been designing 4WD suspension in Australia for decades, with products developed and tested locally rather than adapted from overseas market conditions. This MRA strut kit is backed by manufacturer warranty and is one of the most specified adjustable front kits for the 200 Series among tourers and workshops. You can view the full Dobinsons suspension range for matching rear components and accessories.
This kit suits 200 Series owners running a bullbar, winch and driving lights who need adjustable damping to manage that constant front load without a harsh ride. It's also a good fit for serious tourers who want to firm up compression and rebound for corrugations then soften off for blacktop. If your rear end needs load-levelling for a caravan or camper trailer, our airbag suspension options can complement this front strut kit.
This kit is in stock in Australia and ready for fast dispatch, with our team on hand to confirm fitment and spring rate before you buy. Browse our full lift kit range to compare front and rear options for your 200 Series.
This Dobinsons MRA Adjustable Strut Kit (SKU DMA-FPA200N) is built for the Toyota Land Cruiser 200 Series across all model years from 2007 to 2021, covering UZJ200, VDJ200 and URJ202 chassis codes. It suits both the 4.5L V8 turbo diesel and V8 petrol variants. If you're fitting aftermarket wheels, bullbars or a snorkel, check with our team first so we can confirm there's no clearance conflict. You can also cross-check compatibility using our 200 Series parts finder.
This kit provides a 2" front lift when the included Dobinsons coil springs are fitted and the strut is set to correct ride height. Final lift height can vary slightly depending on the constant accessory load carried on the front of your vehicle. The C-spanners supplied let an installer fine-tune ride height within the strut's adjustment range. This is a front-only kit, so rear lift height depends on whichever rear springs or leaf pack you run separately.
The kit includes two Dobinsons MRA Adjustable Front Struts pre-assembled with coil springs, two new strut top mounts, and a set of C-spanners for ride height adjustment. Mounting hardware is included where applicable. Rear shocks, rear springs and control arms are not part of this kit and are sold separately. Full fitting instructions are supplied with the kit.
Yes. The 3-way damping adjustment allows you to firm up low-speed compression to reduce brake dive and squat when towing, then back it off for unladen driving. The 50mm bore monotube design with remote reservoir resists heat fade during long tows on corrugated or undulating roads. Correct spring rate selection based on your constant front load is important to get the balance right — our team can help you match it to your setup.
Not always, but it depends on your final ride height and articulation needs. At a 2" front lift, factory control arm geometry can shift caster and camber slightly, which alignment can usually correct within spec. If you're also running larger tyres or want improved down-travel, pairing this strut kit with upgraded control arms is worth discussing with our fitment team.
Yes, a wheel alignment is mandatory after installing this strut kit. Changing front ride height alters caster and camber angles, and correct alignment protects tyre wear and steering feel. We recommend allowing a 500km bedding-in period for the springs and seals before the final alignment is set. Skipping alignment can lead to uneven tyre wear and inconsistent handling.
Spring rate for this kit is matched to your constant front accessory load — items like a bullbar, winch, driving lights and long-range tank that are permanently fitted. Occasional loads such as passengers or camping gear don't count toward this figure. If you're unsure of your total constant load, contact our suspension specialists before ordering so we can confirm the right spring is supplied with your strut kit.
A 2" front lift typically creates clearance for larger diameter tyres on a Land Cruiser 200, with many owners running up to 33" tyres depending on wheel offset and any minor trimming. Actual clearance depends on your wheel width, offset and whether the rear is also lifted to match. We recommend checking your specific wheel and tyre combination with our team before ordering to avoid rubbing.
This kit is covered by Dobinsons' manufacturer warranty against manufacturing defects. Warranty claims are handled through 4WD Suspension as your Australian supplier, with our team assisting with any assessment. Correct installation, spring rate selection and wheel alignment are required to keep warranty cover valid. Keep your proof of purchase and fitment records in case a claim is needed.
Yes. The 3-way damping adjustment lets you set the strut softer for comfortable daily and highway driving, then firm it up when loaded or off-road. The monotube remote-reservoir design maintains consistent damping without the fade you can get from smaller-bore twin-tube shocks under repeated use. Many 200 Series owners run this kit as their everyday setup while still having adjustability on hand for touring trips.
Help other 4WDSuspension users shop smarter by writing reviews for products you have purchased.
Add your favourites to cart
Log into or create your Afterpay account, with instant approval decision
Your purchase will be split into 4 payments, payable every 2 weeks
All you need to apply is to have a debit or credit card, to be over 18 years of age, and to be a resident of country offering Afterpay
Late fees and additional eligibility criteria apply. The first payment may be due at the time of purchase
For complete terms visit afterpay.com/terms
