The Dobinsons IMS Front Lift Kit suits the Dodge Ram 1500 DS (2018-2023) and uses a height-adjustable strut with an adjustable lower spring perch, giving you a 2" to 3" front lift from one kit rather than a single fixed height. Each strut pairs with a Dobinsons coil spring matched to the factory front weight, so ride quality stays controlled whether you run 2" for touring or 3" to clear a winch bar. This front lift kit is Australian stock, backed by manufacturer warranty, with fitment guidance from our in-house suspension team.
Browse all compatible suspension parts for your 50-75Mm Front Lift Kit Dodge Ram 1500 using our parts finder.
| Make | Model | Series | Years | Engine |
|---|---|---|---|---|
| Dodge | Ram 1500 | DS | 2018-2023 | 5.7L Hemi V8 & 3.6L Pentastar V6 (petrol variants) |
Not sure if this fits your vehicle? Contact our suspension experts or check our FAQ page.
Lift height compliance: Suspension lifts of this size may exceed your state's allowable limit without engineering certification. Check your state's light vehicle modification rules (VSB14/NCOP) before fitting.
Choose your front lift setting based on the weight sitting over the front axle once accessories are fitted. A bull bar, winch, driving lights and a bash plate all add constant load to the front end and can settle ride height lower than standard. Run the strut toward the 3" end of its range if you're carrying this front accessory weight, or toward 2" for a closer-to-stock stance with lighter front-end fitment.
Fitment is a bolt-in strut and spring swap best handled by an experienced DIY installer or your usual workshop, with the adjustable perch set to your chosen height before final tightening. Wheel alignment is mandatory after fitting — front castor and camber shift once ride height changes. Allow a 500km bedding-in period for the springs to settle to their working height before any final alignment check. If you're lifting toward the 3" end of the range, consider pairing this kit with upgraded control arms to correct front geometry and CV joint angles.
Dobinsons is an Australian-owned suspension manufacturer that engineers and tests its lift kits under local conditions rather than relying solely on overseas data. This IMS kit carries a manufacturer warranty on strut and spring components, and is one of the more common front lift options fitted to the Ram 1500 DS by Australian workshops. You can view the full Dobinsons range for matching rear leaf springs, shocks and control arms.
This kit suits Ram 1500 owners fitting a bull bar and winch who need front height back to correct, and tourers wanting tyre clearance for a larger front tyre without a full suspension overhaul. Tradespeople carrying tray or canopy weight over the rear axle should also look at airbag suspension to support rear load independently of this front-only kit.
In stock in Australia with fast dispatch and fitment support from our team — browse our full lift kit range or check compatible parts via our Dodge Ram parts finder.
New to Ram suspension? Read our guide to common Ram suspension problems and how to fix them.
This kit is built for the Dodge Ram 1500 DS built between 2018 and 2023, covering both 5.7L Hemi V8 and 3.6L Pentastar V6 variants. It is a front-only kit and does not include rear components. If your Ram is outside this build range or a different series, check with our team before ordering using the details on our contact page.
The Dobinsons IMS strut is adjustable across a 2" to 3" front lift range, set at the lower spring perch during installation. You choose the height within that range rather than being locked to one fixed lift. This lets you dial in clearance for larger tyres or offset the weight of a front bull bar and winch.
Please note that all assembled struts are dispatched at a height based on our experience and the manufacturer’s specifications for the advertised lift. Coil springs and leaf springs are also manufactured according to the advertised height and constant-load rating. Actual vehicle height may vary depending on the vehicle and the weight of fitted accessories. Further adjustment may therefore be required after installation. The installer may use coil spacers or adjust the struts at their discretion to achieve the desired height. We are not responsible for vehicle-specific height variations or any additional adjustments required after installation.
The kit includes 2 x Dobinsons IMS height-adjustable front struts and 2 x matched front coil springs, along with mounting hardware for the strut-to-knuckle and strut-to-chassis connections. Strut top mounts are included where specified for this application. Rear shocks, rear springs and upper control arms are not part of this front kit and are available separately.
This is a front lift kit, so it primarily affects front ride height and load-carrying rather than towball weight, which sits over the rear axle. If you tow regularly, pair this front kit with a rear leaf spring or airbag suspension upgrade to support the added rear load. Our team can advise on a front-and-rear combination based on your trailer weight.
At the higher end of the 2" to 3" adjustment range, front control arm angles and CV joint operating angles change from standard. We recommend pairing this kit with upgraded control arms if you're running closer to the 3" setting, to correct geometry and reduce wear on CV joints and bushes. At the 2" setting, factory control arms are generally retained.
Yes, wheel alignment is mandatory after installing this kit. Changing front ride height alters castor and camber angles, and an alignment corrects this to factory-spec tolerances or the settings recommended for your chosen lift height. Skipping alignment will cause uneven tyre wear and can affect steering feel.
The coil springs supplied with this kit are matched to the standard front axle weight of the Ram 1500 DS. If you're carrying substantial front-end accessory weight such as a heavy bull bar and dual-battery winch setup, speak with our team about a front spring rate suited to that load before ordering.
Setting the strut toward the 3" end of the adjustment range typically provides useful clearance for a moderately larger front tyre than standard. Actual clearance depends on your wheel offset and tyre width, so check your specific tyre size against your Ram's guards before purchasing tyres. Our fitment support team can talk through tyre and wheel combinations for this kit.
This Dobinsons IMS kit is covered by manufacturer warranty on the strut and spring components from the date of purchase. Warranty terms are handled through 4WD Suspension as an authorised Dobinsons stockist. Contact our team if you need the specific warranty documentation for your purchase.
Yes, this kit is designed to retain factory-style ride comfort at the 2" setting for daily driving, with the option to move toward 3" for touring or off-road use. The coil spring rate is matched to standard front axle weight, so unloaded ride quality stays close to stock at the lower end of the adjustment range. A 500km bedding-in period is recommended after fitting before final alignment.
Help other 4WDSuspension users shop smarter by writing reviews for products you have purchased.
Add your favourites to cart
Log into or create your Afterpay account, with instant approval decision
Your purchase will be split into 4 payments, payable every 2 weeks
All you need to apply is to have a debit or credit card, to be over 18 years of age, and to be a resident of country offering Afterpay
Late fees and additional eligibility criteria apply. The first payment may be due at the time of purchase
For complete terms visit afterpay.com/terms
